- 您现在的位置：买卖IC网 > Sheet目录1236 > PL-USB-BLASTER-RB (Altera)CABLE PROGRAMMING USB
2–4
Chapter 2: USB-Blaster Specifications
USB-Blaster Connections
Table 2–2. USB-Blaster Female Plug Signal Names & Programming Modes
AS Mode
PS Mode
JTAG Mode
Pin
1
2
3
Signal Name
DCLK
GND
CONF_DONE
Description
Clock signal
Signal ground
Configuration done
Signal Name
DCLK
GND
CONF_DONE
Description
Clock signal
Signal ground
Configuration done
Signal Name
TCK
GND
TDO
Description
Clock signal
Signal ground
Data from device
4
VCC(TRGT) Target power supply
VCC(TRGT)
Target power
VCC(TRGT)
Target power supply
supply
5
nCONFIG
Configuration
nCONFIG
Configuration
TMS
JTAG state machine
control
control
control
6
7
nCE
DATAOUT
Cyclone chip enable
Active serial data
—
nSTATUS
No connect
Configuration
—
—
No connect
No connect
out
status
8
nCS
Serial configuration
—
No connect
—
No connect
device chip select
9
10
ASDI
GND
Active serial data in
Signal ground
DATA0
GND
Data to device
Signal ground
TDI
GND
Data to device
Signal ground
1
The circuit board must supply V CC(TRGT) and ground to the USB-Blaster
cable for the I/O drivers.
Circuit Board Header Connection
The circuit board's 10-pin male header, which connects to the USB-Blaster cable's
10-pin female plug, has two rows of five pins. These pins are connected to the device’s
programming or configuration pins. Figure 2–4 shows the dimensions of a typical
10-pin male header.
1
Although a 10-pin surface mount header can be used for the JTAG, AS or PS
download cable, Altera recommends using a through-hole connector because of the
repeated insertion and removal force needed.
Figure 2–4. 10-Pin Male Header Dimensions
Top View
Side View
0.100
Dimensions are shown in inches
0.100
0.025 S
? April 2009 Altera Corporation
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
PL155-47
TRS PLUG WRENCH CRIMP STR 3-LUG
PL155AC-201
TRS PLUG FULL CRIMP STR 3-LUG
PL1MWLT-026
MINI WECO PATCH PLUG FOR CABLE
PL20-2
BNC PLUG 50 OHM WRENCH CRIMP STR
PL20-3
BNC PLUG 50 OHM WRENCH CRIMP STR
PL20-5
BNC PLUG 50 OHM WRENCH CRIMP STR
PL3155-47
TTM CABLE PLUG CRIMP STR CABLE
PL3455ACP-221
TWINAX PIN CONTACT USE W/CABLE
相关代理商/技术参数
PL-USB-BLASTER-RCN
功能描述:可编程逻辑 IC 开发工具 USB Program Cable FPGA CPLD & Ser Conf RoHS:否 制造商:Altera Corporation 产品:Development Kits 类型:FPGA 工具用于评估:5CEFA7F3 接口类型: 工作电源电压:
PL-USB-BLASTER-RCN RENT
制造商:Altera Corporation 功能描述:CABLE PROG DOWNLOAD USBRENT
PLUTO
制造商:MITEL 制造商全称:Mitel Networks Corporation 功能描述:Dual Mode CDMA/AMPS Baseband Interface
PLV-025
制造商:QUALTEK 制造商全称:QUALTEK 功能描述:25Watts Single Output LED Driver
PLV-025S012
功能描述:LED电源 LED DRIVER 25W C/V 12V 80X78X27 RoHS:否 制造商:Cree, Inc. 工作模式:Constant Voltage (CV) 输出功率额定值: 输入电压:220 V to 240 V 输出端数量:1 输出电压（通道 1）:40 V 输出电流（通道 1）:900 mA 安装风格:Screw 尺寸:90 mm L x 90 mm W x 37.5 mm H 商用/医用:Commercial
PLV-025S018
功能描述:LED电源 LED DRIVER 25W C/V 18V 80X78X27 RoHS:否 制造商:Cree, Inc. 工作模式:Constant Voltage (CV) 输出功率额定值: 输入电压:220 V to 240 V 输出端数量:1 输出电压（通道 1）:40 V 输出电流（通道 1）:900 mA 安装风格:Screw 尺寸:90 mm L x 90 mm W x 37.5 mm H 商用/医用:Commercial
PLV-025S024
功能描述:LED电源 LED DRIVER 25W C/V 24V 80X78X27 RoHS:否 制造商:Cree, Inc. 工作模式:Constant Voltage (CV) 输出功率额定值: 输入电压:220 V to 240 V 输出端数量:1 输出电压（通道 1）:40 V 输出电流（通道 1）:900 mA 安装风格:Screw 尺寸:90 mm L x 90 mm W x 37.5 mm H 商用/医用:Commercial
PLV-025S036
功能描述:LED电源 LED DRIVER 25W C/V 36V 80X78X27 RoHS:否 制造商:Cree, Inc. 工作模式:Constant Voltage (CV) 输出功率额定值: 输入电压:220 V to 240 V 输出端数量:1 输出电压（通道 1）:40 V 输出电流（通道 1）:900 mA 安装风格:Screw 尺寸:90 mm L x 90 mm W x 37.5 mm H 商用/医用:Commercial